Exactly How to Install a Tub in Your Bathroom
Exactly How to Install a Tub in Your Bathroom
Blog Article
They are making several great annotation about How to Install a Bathtub Yourself overall in the content beneath.
Installing a tub isn't specifically rocket science, however it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old tub with a brand-new one is also a moderately hard project. If the old bathtub is readily easily accessible, the task can move immediately; if you need to open a wall surface to get rid of the old tub as well as place the new tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and set in the brand-new one. Make sure you have certified on your own for the work and are comfortable trying it. Rather than employing a contractor to take over a halfway-completed task, it is better to think about using one before you start. Opportunities are you may require a specialist plumber to make tube connections.
This post will certainly help you set up a brand-new bathtub in your restroom if you have actually currently purchased a brand-new bathtub and don't require to transform the arrangement of your previous water system pipelines.
Your tools and product list should comprise the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is detach the water system. After doing so, activate the faucets to drain any water staying in the system. The procedure of getting rid of the existing faucets can be fairly problematic due to the restricted gain access to that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will come from the pipes. When the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Before proceeding to fit the new taps, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washers are in area between the tap and also the sink. Secure the faucet in place with the supplier offered backnut. Once the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind ought to be connected to the faucet ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Utilizing both wood boards under its feet, put the bathtub in the needed position. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the bathtub up until the level reads degree.
To mount taps, fit all-time low of the furthest versatile faucet connector to the suitable supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the supply of water as well as check all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally examine the overflow electrical outlet and the typical outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as sealing around the tub must wait till the tub has actually been made use of at the very least when as this will certainly settle it into its final position.
Preparing for the Installation
First of all, the supporting frame supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make certain that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom need to now prepare to be fitted in its final placement.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to break a rigid seal, creating the water to pass through the wall between the bathroom as well as the tiling, causing complications with dampness and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your components as well as fittings. They are sold in tubes as well as cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the tub with water prior to securing, to enable the activity experienced when the bathtub remains in usage. The sealant can split rather very early if you do not consider this movement before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily offered on the market. It is recommended to fit the floor tiles using waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading about Installing A Bathtub? Give feedback down the page. We would be glad to know your insights about this blog entry. We are looking forward that you come back again before long. You should take a moment to promote this article if you appreciated it. We truly appreciate reading our article about Tools You Need to Install a New Bathtub .
Hire A Pro Report this page